Commission Regulation (EU) 2019/1939 of 7 November 2019 amending Regulation (EU) No 582/2011 as regards Auxiliary Emission Strategies (AES), access to vehicle OBD information and vehicle repair and maintenance information, measurement of emissions during cold engine start periods and use of portable emissions measurement systems (PEMS) to measure particle numbers, with respect to heavy duty vehicles (Text with EEA relevance)

‘1 In order to receive an EU type-approval of an engine system or engine family as a separate technical unit, an EU type-approval of a vehicle with an approved engine system with regard to emissions, or an EU type-approval of a vehicle with regard to emissions, the manufacturer shall, in accordance with the provisions of Annex I, demonstrate that the vehicles or engine systems or engine families are subject to the tests and comply with the requirements set out in Articles 4 and 14 and in Annexes III to VIII, X, XIII and XIV. The manufacturer shall also ensure compliance with the specifications of reference fuels set out in Annex IX. In the case of dual-fuel engines and vehicles, the manufacturer shall, in addition, comply with the requirements set out in Annex XVIII. In order to receive an EU type-approval of a vehicle with an approved engine system with regard to emissions, or an EU type-approval of a vehicle with regard to emissions, the manufacturer shall also demonstrate that the requirements laid down in Article 6 of and Annex II to Commission Regulation (EU) 2017/2400 are met with respect to the vehicle group concerned. However, that requirement shall not apply where the manufacturer indicates that new vehicles of the type to be approved will not be registered, placed on the market or entered into service in the Union on or after the dates laid down in points (a), (b) and (c) of paragraph 1 of Article 24 of Regulation (EU) 2017/2400 for the respective vehicle group.

‘2 In order to receive an EU type-approval of a vehicle with an approved engine system with regard to emissions, or an EU type-approval of a vehicle with regard to emissions, the manufacturer shall ensure compliance with the installation requirements set out in Section 4 of Annex I and, in the case of dual-fuel vehicles, with the additional installation requirements set out in Section 6 of Annex XVIII.’;

‘3 In order to receive an extension of the EU type-approval of a vehicle with regard to emissions type-approved under this Regulation with a reference mass exceeding 2380 kg but not exceeding 2610 kg, the manufacturer shall meet the requirements set out in Section 5 of Annex VIII.’;

‘6 In order to receive an EU type-approval of an engine system or engine family as a separate technical unit or an EU type-approval of a vehicle with regard to emissions for the purposes of obtaining universal fuel-range type-approval, a restricted fuel-range type-approval or a fuel-specific type-approval, the manufacturer shall ensure compliance with the requirements set out in Section 1 of Annex I.’;

‘3 Together with the application, the manufacturer shall provide a documentation package that fully explains any element of design which affects emissions, the emission control strategy of the engine system, the means by which the engine system controls the output variables which have a bearing upon emissions, whether that control is direct or indirect, anti-tampering measures and fully explains the warning and inducement system required by Sections 4 and 5 of Annex XIII. The documentation package shall be identified and dated by the approval authority and kept by that authority for at least 10 years after the approval is granted. The documentation package shall consist of the following parts: the information set out in Section 8 to Annex I, an AES documentation package, as described in Appendix 11 of Annex I to this Regulation in order for the approval authorities to be able to assess the proper use of AES. At the request of the manufacturer, the approval authority shall conduct a preliminary assessment of the AES for new vehicle types. In that case, the manufacturer shall provide the draft AES documentation package to the approval authority between 2 and 12 months before the start of the type-approval process. The approval authority shall make a preliminary assessment on the basis of the draft AES documentation package provided by the manufacturer. The approval authority shall make the preliminary assessment in accordance with the methodology described in Appendix 2 of Annex VI. The approval authority may deviate from that methodology in exceptional and duly justified cases. The preliminary assessment of the AES for new vehicle types shall remain valid for the purposes of type approval for a period of 18 months. That period may be extended by a further 12 months if the manufacturer provides the approval authority with proof that no new technologies have become available on the market that would change the preliminary assessment of the AES. A list of AES which were deemed non-acceptable by approval authorities shall be compiled yearly by the Forum for Exchange of Information on Enforcement and made available to the public by the Commission.’

‘1 The manufacturer shall submit to the approval authority an application for EU type-approval of a vehicle with an approved engine system with regard to emissions.’;

‘1 The manufacturer shall submit to the approval authority an application for EU type-approval of a vehicle with regard to emissions.’;

‘3 With effect from 1 January 2021, national authorities shall refuse, on grounds relating to emissions, to grant EU type-approval or national type-approval in respect of new types of vehicle or engine which do not comply with the requirements of this Regulation as amended by Commission Regulation (EU) 2019/1939 . By way of derogation from the first subparagraph, new types of positive-ignition engines, type 1A dual-fuel engines and type 1B dual-fuel engines (in dual-fuel mode), and vehicles equipped with such engines, shall comply with the maximum allowed conformity factor for PM number according to point 6.3 of Annex II with effect from 1 January 2023. However, as from 1 January 2021, the particle number work window conformity factor and CO2 mass window conformity factor shall be stated in the PEMS demonstration test results on the type-approval certificate for monitoring purposes.

4 With effect from 1 January 2022, national authorities shall, in the case of new vehicles which do not comply with the requirements of this Regulation as amended by Regulation (EU) 2019/1939, consider certificates of conformity issued in respect of those vehicles to be no longer valid for the purposes of Article 48 of Regulation (EU) 2018/858 and shall, on grounds relating to emissions, prohibit the registration, making available on the market and entry into service of such vehicles. By way of derogation from the first subparagraph, with effect from 1 January 2024, national authorities shall, in the case of new vehicles equipped with positive-ignition engines, type 1A dual-fuel engines and type 1B dual-fuel engines (in dual-fuel mode) which do not comply with the maximum allowed conformity factor for PM number according to point 6.3 of Annex II and the requirements of this Regulation as amended by Regulation (EU) 2019/1939, consider certificates of conformity issued in respect of those vehicles to be no longer valid for the purposes of Article 48 of Regulation (EU) 2018/858 and shall, on grounds relating to emissions, prohibit the registration, making available on the market and entry into service of such vehicles. However, as from 1 January 2022, the particle number work window conformity factor and CO2 mass window conformity factor shall be stated in the PEMS demonstration test results on the type-approval certificate for monitoring purposes. With effect from 1 January 2022 and except in the case of replacement engines for in-service vehicles, national authorities shall on grounds relating to emissions prohibit the making available on the market and entry into service of new engines which do not comply with the requirements of this Regulation as amended by Regulation (EU) 2019/1939. By way of derogation from the third subparagraph, with effect from 1 January 2024, and except in the case of replacement engines for in-service vehicles, national authorities shall, on grounds relating to emissions, prohibit the making available on the market and entry into service of new positive-ignition engines, new type 1A dual-fuel engines and new type 1B dual-fuel engines (in dual-fuel mode) which do not comply with the requirements of this Regulation as amended by Regulation (EU) 2019/1939.

This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union. It shall apply from 1 January 2021. Article 1(15) shall apply from the date of entry into force.